0086-755-26458295
Room 903, Building B, Nanchang Jianyu 2nd Industrial Park, Nanchang Community, Xixiang St., Bao'an Dist., Shenzhen, Guangdong, China (Mainland)
1. Wireless IR remote control Can set up all SRNE solar street lamps controllers.
2. The data communications base on the multiple handshake protocol and
compression algorithm which made the data transfer fast and accurate.
3. Work on two batteries (Model: AA).
4. LCD indicator shows the parameter and data.
5. The remote control will enter intelligent sleep state after One min no any operate,
and press any key to resume.
6. Low-energy sleep mode, less than 0.1uA.
7. Fast wake-up function.
8. Battery capacity indicator.
9. Emergency light and hazard lights.
10. with ergonomic design, suitable for the hand-held operation.
| Item | Name abbreviation | data scope | Name describe | step-length | unit | Factory Default |
a | 1st time | 0 ~ 15H | The first working time | 1H | hour | 4 hour |
b | 1st power | 0 ~ 100% | The first working time power | 10% | Power (percentage) | 100% |
| c | 2nd time | 0 ~ 15H | The second working time | 1H | hour | 0 hour |
d | 2nd power | 0 ~ 100% | The second working power | 10% | Power (percentage) | 70% |
| e | 3rd time | 0 ~ 15H | The third working time | 1H | Hour | 4 hour |
| f | 3rd power | 0 ~ 100% | The third working power | 10% | Power (percentage) | 50% |
| g | Mor time | 0 ~ 15H | Lighting time in the morning | 1H | Hour | 0 hour |
| h | Mor power | 0 ~ 100% | Lighting power in the morning | 10% | Power (percentage) | 30% |
| i | L-Con-V | 5 ~ 11V | Light control voltage | 1V | Volt | 5V |
| j | L-Con-DT | 5 ~ 50Mins | Light control delay time | 5M | Min | 5min |
| k | L-Current | 0.15~ 3.42A | LED load current | 0.03A | A | 0.30A |
| l | L-On-EN | 0 ~ 1 | Lights on every night | 1 | 0:Off1:On | 1 |
| m | Smart Power | 0 ~ 1 | Smart power control | 1 | 0:Off1:On | 0 |
| n | Over-DV | 9.8 ~ 11.8V | over-discharging protected voltage | 0.2V | Volt | 11.0V |
| o | Over-DRV | 12.0 ~ 13.0V | over-discharging recover voltage | 0.2V | Volt | 12.6V |
| p | Boost-CV | 14.2 ~ 15.0V | Ascending charging voltage | 0.2V | Volt | 14.4V |
| Battery model | (AA)× 2pcs |
| power supply voltage | 3.0V |
| Effective distance | <5m |
| power consumed of sleep mode | <0.2uA |
| Normal power consumed | 5mA |
| Send instant power consumed | <50mA |
| Light consumption | 12mA |
| Backlight consumption | 15mA |
| Size | 122mm×61.5mm×22mm(L×W×H) |
| Weight | 60g(without the battery) |
| Auto power off time | 1 min |
| Backlight time | 10 S |
| Lighting time | 10 S |
| 2000mAH battery setting quantity | 50000 pcs(back light and lights both are closed) |
| Working temperature | -25℃ ~ 55℃ |
1.Power on: press any key to start up, then the remote control be rouse and executive the function under the key u press.
2.Power off: System will power off automatically then enter intelligent sleep state after 1min later no any operate.
3.Browse the parameter: after power on, press “+” and “–”key can browse the parameter preset before.
4. Model Selection: after power on, Press the "+" "-" key to highlight the stays on the models to choose, then short press "set" key to /confirm/i, remote control will shedding for 1 second, then enter into the "parameter setting" interface.
5. Modify the parameters: Browse to the parameter which u want to set, press ”set” key, the data begin flash, then press “+” and “–”key to adjust. Setting over, press the ”set” key to /confirm/i.
6.Sending parameter: After all the parameters are set up, aim at the solar charge controller and press the “send” key. If sending successfully, three LED lights of thecontroller will flash, at the same time the remote control will keep a long sound; If failed, the remote control will keep three short sound and prompt delivery failure.
7.Read the state: aim at the solar controller and press the “state” key, the remote control will read the running state of the controller, If reading successfully, the remote control will keep a long sound and store the data; If failed, the remote control will keep three short sound and will show the old status.
8.Read the parameter: aim at the solar controller and press the “parameter” key, the remote control will read the setting value of the controller. If reading successfully,the remote control will keep a long sound and store the data(if press the “send” key now, the store parameter will be send immediately) ; If failed, the remote control will keep three short sound and will show the parameter which u are in setting.
| carton size | package situation |
| 335*300*210mm | 42 pieces in a carton |
Shenzhen Shuori New Energy technology Co.,Ltd.has founded in 2009 with independent intellectual property,right and brand .We set R&D,manufacture,sales and service as a whole ,specialized in solar controller,system solutions,application system and engineering service,solar PV power supply related technology development of national high tech enterprise.
